Turn a simple pallet into a lush and green vertical garden with our DIY Pallet Vertical Garden tutorial in just a few easy steps!
Find a Pallet
The first thing you need to do to make this vertical pallet garden is–obviously–find a pallet. Here’re the two good articles (here and here) that outline where to find free or low cost pallets for this DIY. Don’t just take the first pallet you find. You’re looking for one with all the boards in good condition, no nails sticking out, no rotting, etc. If you intend to put edibles in your pallet, be sure to find one that was heat treated as opposed to fumigated with pesticides.
Collect Your Supplies
For this project, you’ll need:
- The pallet you found
- 2 large bags of potting soil
- 16 six packs of annual flowers (one six pack per opening on the face of the pallet, and two six packs per opening on the top of the completed pallet garden)
- A small roll of landscape fabric
- A staple gun
Get Your Pallet into Shape
Once you’ve dragged your pallet home, give it a once-over. Are any of the boards a little loose? Is the wood chipping in places? Nail down any loose boards, and use sandpaper to smooth down any rough spots.
Let the Stapling Begin!
Decide which side of the pallet will be the bottom when the pallet garden is completed and leaning against the wall. You are going to be covering the bottom, back, and sides with landscape fabric, leaving the spaces between the slats and the top uncovered (you’ll be planting flowers in the uncovered spaces).
Lay the pallet face down. Roll the landscape fabric over the back. Cut two identically sized pieces that are long enough to go from the top edge of the back of the pallet and wrap all the way around the bottom, plus a few extra inches.
Hold the two pieces of landscape fabric together as if they were one piece of fabric. Fold over the top edge by one inch and center it on the top board of the back of the pallet. Staple the fabric into place near the top edge of the top board. Smooth the fabric out to the left and right and pull it taut. Staple the fabric down on the top, the right edge of the top board. Repeat on the left side. Fill in between those three staples with one staple every two inches along the top edge of the top board.
When the top of the landscape fabric is securely attached to the top, backboard, smooth the fabric down, and repeat the process along the bottom edge of the bottom board, except don’t fold the fabric under, leave a long flap on the bottom.
Pulling the fabric tautly along the bottom, fold the cut edge under, and staple the fabric down along the front edge of the bottom. Smooth the fabric out to the left and right and staple every two inches along the front edge of the bottom.
Now for the sides. Start near the bottom and fold the excess fabric inwards as if you were wrapping a present. Fold the cut edge of the fabric under and staple it down near the front, bottom edge of the side facade. Smooth the fabric out and place a staple every two inches along the front edge of the side of the pallet. The fabric should be taut but not in danger of tearing. Repeat on the other side of the pallet.
You should now have a pallet with landscape fabric wrapped around the sides, back, and bottom. Place more staples along the spine of the back side of the pallet, and anywhere else you think the fabric needs to be held down so that soil can’t creep into places you don’t want it to go.
Now for the Fun Part–Planting!
Bring the pallet close to wherever it’s final spot will be and lay it down face up. You’re going to plant it while it’s laying flat on the ground.
First, slide the plants into what will be the top. Plant everything very tightly, you should have to shoehorn the last plant into place practically. Now that you have capped the top, pour the entire first bag of potting soil on top of the pallet. Push the soil into the pallet between the slats and smooth it out so that the soil is level. Repeat with the second bag of potting soil.
Push potting soil into the bottom cavity, so that there is a trench directly below one of the bottom openings. Plant six plants in the trench, so that they are very tightly fitted into the opening. Repeat with the other bottom opening. Now push the potting soil up against those flowers you just planted, making a trench beneath one of the openings in the second row. Plant your flowers tightly in that opening. Repeat for all the remaining openings.
When you’re doing the planting, you should have plants that are completely covering every opening (i.e., there shouldn’t be any place for the soil to fall out). There should also be soil firmly pushed into every part of the pallet where there aren’t plants.
Caring For your Pallet Garden
Once your pallet garden is completed, you should know how to care for it. The first thing to do is leave the pallet flat on the ground for a couple of weeks (watering when needed) so that the roots can start to grow in and hold all the plants in place. This is the most important step, and you must not skip it. Some soil does fall out, but it seems to be okay.
Water your pallet regularly as they dry out quickly. Pay special attention to the bottom two openings. They seem to be the driest. Fertilize with water-soluble fertilizer added to your watering can (follow package instructions for the amount and frequency).